Fork Truck Operator Certification - BNZ Materials - North Billerica MA - CLOSED
2025-03-06 07:00 - 15:00 (America/New_York) | MA
Industrial Forklift Safety Training
This forklift operator safety training course is a focused operations and safety training for operators.
Industrial forklifts are covered in this class. Rough terrain forklifts can be covered by special request. Operator qualification will be performed. A completion of safety training certificate is awarded by Cranes 101. Operators who successfully pass the hands on qualification receive a Qualified Operator certificate as well as a wallet card

Material covered in this course:
Fork truck maneuvering
The mechanics of the Fork Truck
Daily inspections
Fuel/Electric storage
ANSI and OSHA standards
Safe practices
Proper care and maintenance
Physics 101
This training meets or exceeds all requirements of OSHA 1910.172
For more information as to the content of this class, please view the descriptions here. (Hyperlink the “here” to the specific page on the web site showing this class)
Training Length:
>>3 to 4 Hour Course
Use this form below to request more information. One of our staff will be in contact with you soon.

OPERATOR QUALIFICATIONS
In addition to equipment specific safety training, OSHA requires operators to be evaluated on the equipment they operate. While this can be done by a supervisor, most of our customers prefer a 3rd party evaluation. Operators receive a certificate as well as a wallet card which includes the make, model and serial number of the equipment they were tested on.
We offer hands-on qualification on various types of equipment including forklift, MEWP, bucket trucks and mobile cranes. We can provide the evaluations with or without a safety training class, but recommend holding both on the same day – safety training class in the morning, lunch break, qualifications in the afternoon.
Please contact our office at 508-966-4100 or use this form below to request more information. One of our staff will be in contact with you soon.

Overhead Crane Operator Safety Course with Basic Rigging - Rolls Royce - CLOSED
2025-03-07 08:00 - 16:00
This overhead crane operator safety training course covers operation, inspection, rigging, owners’ responsibility and operators’ responsibility. It includes hands on operator evaluations as well.
This training meets the requirements mandated in OSHA Overhead and gantry cranes 29CFR1910.179(b)(8), ASME B30.16, B30.17 and OSH act of 1970 General Duty Clause 5(a)(1)
A completion of safety training certificate is awarded by Cranes 101. Operators who successfully pass the hands on qualification receive a Qualified Operator certificate as well as a wallet card

For more information as to the content of this class, please view the description here.
Training Length:

3 to 4 Hours for the course; additional time needed if operator qualification to be included

Use this form below to request more information. One of our staff will be in contact with you soon.

2A/1B/1C MA Hoisting License Preparation/Continuing Education Course - Bellingham MA - OPEN
2025-03-08 08:00 - 17:00
You are required to have a Hoisting Engineer license to operate any equipment that lifts over 10 ft in height, over 500 lbs in weight or over 1/4 yard of bucket capacity in Massachusetts, per the 520 CMR 6.00 law. This course is designed to prepare the attendee for successful completion of the Hoisting Engineers’ license test. Cranes101 recommends that before taking this hoisting license preparation course to be sure to apply for a test date with the Commonwealth of Massachusetts. Then take the class closest to the test date.
For more information as to the content of this class, please view the descriptions here.
Attendees are only required to attend the course(s) they need. If you are looking for a license preparation for another restriction that is not listed, please let us know. We offer all license classes (1-3’s). We do not have license preparation classes for the 4’s, just online continuing education courses.
This is also a safety seminar that will earn the operator his/hers required CEU to maintain the hoisting engineer license.
Training Length – License Preparation
2A: 8-12 1B: 12-5:30 (1C will be incorporated as part of 1B)

Training Length – Continuing Education
2A: 8-12 — 1C: 12-4:00 — 1B 12-5:00
Use this form below to request more information on attending one of our monthly open classes or to host a class at your location. One of our staff will be in contact with you soon.

Overhead Crane Operator Safety Course with Qualifications - Primetals - CLOSED
2025-03-10 14:30 - 20:30

Signalperson with Basic Rigger - Poyant Signs - CLOSED
2025-03-14 08:00 - 16:00
This live signalperson/basic rigger certification course covers:

Rigging component identification
Mathematical calculations
Sling selection
Rigging inspection
Wire rope and chain design
Proper rigging techniques

Proper use of the ANSI hand signals
Crane limitations
Crane characteristics and dynamics
Signalperson requirements per OSHA 1926.1419-1926.1422
Working near power lines
Voice signals

This training meets the requirements mandated in OSHA 1926.1419 through
1926.1422 and 1926.1428, and ANSI/ASME B30 standards.
For more information as to the content of this class, please view the descriptions here.
Training Length:

4 to 6 hour course

Participants will receive a card certifying that they have successfully completed this training that they should carry on the job-site.
Use this form below to request more information about our signalperson/rigger course. One of our staff will be in contact with you soon.

Signalperson with Basic Rigging and Practical Exam - Florence Electric - MA - CLOSED
2025-03-14 08:00 - 16:00

Mobile Crane Nationally Accredited Certification Program - MACK Industries - Mt. Vernon OH - OPEN REGISTRATION - Call 508-966-4100
2025-03-17 08:00 - 2025-03-19 16:00
These all mobile crane nationally accredited certificate courses are NCCER/OSHA/ANSI approved programs for licensing crane operators. Crane operators must be licensed to operate per OSHA Subpart CC.
For more information as to the content of this class, please view the descriptions here. The list below shows the types of cranes this course can cover, depending on what the students operate on the job. Please specify what type of crane you will be operating when you pre-register, if possible.

Fixed/rotating boom trucks
Telescopic boom truck/rough terrain crane/all terrain crane
Lattice boom cranes

TCIA Members save 10% and will earn 21 CTSP CEU’s when the course is completed.
If you are a member of the ISA, our training is certified for the following:

8 Practice
8 Management
16 Climber Specialist
16 Certified Arborist
16 Utility Specialist
16 Municipal Specialist – 16 Aerial Lift

Training Length:
Day One

Classroom instruction on crane operator safety

Day Two*

Classroom instruction in the morning – Testing (written and/or practical exams) begins after lunch

Day Three*

Remaining Exams (written and/or practical)

*Exam schedule may vary based on class size, weather and practical examiner/proctor availability.
Both the written and the practical examinations must be passed with a score of 80 or higher before a nationally accredited crane operator license can be granted.

FOR OPEN CLASSES USE THIS BELOW (AND BE SURE TO DELETE THIS LINE BEFORE POSTING)
Use this form below to pre-register for this Mobile Crane Nationally Accredited Certificate Course or request more information. One of our staff will be in contact with you soon.

Bucket Truck Operator Safety Training with Operator Evaluations - Town of Barnstable - CLOSED
2025-03-18 08:00 - 16:00
This bucket truck operator safety training class is focused on operations and safety training for operators and ground workers. Material covered in this course:

Bucket truck setup
The mechanics of the bucket truck
Daily inspections
Working near electricity
ANSI and OSHA standards
Proper harness/belt configurations
Emergency procedures
Proper care and maintenance
Suspension trauma

This training meets or exceeds all requirements of OSHA, ANSI A92.2 and your insurance company.
There will be hands-on review of the equipment. Our trainer will go over proper pre-use inspections as well as proper setup of the bucket truck on-site. Each operator will be required to run through a variety of tasks to insure competence on the equipment. You must qualify on the equipment you use or on equipment that is the same configuration as your equipment. Please make arrangements to have your bucket truck on site for compliance.
For more information as to the content of this class, please view the description here.
Training Length:

4-5 hours safety training course
Allow 15-20 minutes per qualification
Recommend maximum of 12-14 attendees (7 minimum)

Use this form below to request more information about our bucket truck operator safety course. One of our staff will be in contact with you soon.

OPERATOR QUALIFICATIONS
In addition to equipment specific safety training, OSHA requires operators to be evaluated on the equipment they operate. While this can be done by a supervisor, most of our customers prefer a 3rd party evaluation. Operators receive a certificate as well as a wallet card which includes the make, model and serial number of the equipment they were tested on.
We offer hands-on qualification on various types of equipment including forklift, MEWP, bucket trucks and mobile cranes. We can provide the evaluations with or without a safety training class, but recommend holding both on the same day – safety training class in the morning, lunch break, qualifications in the afternoon.
Please contact our office at 508-966-4100 or use this form below to request more information. One of our staff will be in contact with you soon.

Bucket Truck Operator Safety Training with Operator Evaluations - Town of Holbrook - CLOSED
2025-03-21 08:00 - 16:00

Signalperson with Basic Rigger - CWhite Marine - Danvers - CLOSED
2025-03-22 08:00 - 16:00
This live signalperson/basic rigger certification course covers:

Rigging component identification
Mathematical calculations
Sling selection
Rigging inspection
Wire rope and chain design
Proper rigging techniques
Proper use of the ANSI hand signals
Crane limitations
Crane characteristics and dynamics
Signalperson requirements per OSHA 1926.1419-1926.1422
Working near power lines
Voice signals
Practical Exam for each student on signals, ropes and slings per customer request and customized to their application

This training meets the requirements mandated in OSHA 1926.1419 through
1926.1422 and 1926.1428, and ANSI/ASME B30 standards.
For more information as to the content of this class, please view the descriptions here.
Training Length:

6 to 8 hour course

Participants will receive a card certifying that they have successfully completed this training that they should carry on the job-site.
Use this form below to request more information about our signalperson/rigger course. One of our staff will be in contact with you soon.

3A MA Hoisting License ISP and Overhead Crane Safety with Qualifications - Phillips Medisize - CLOSED
2025-03-24 07:00 - 15:00

Bucket Truck Operator Safety Training with Evaluations - MIIA - Town of Leominster - CLOSED
2025-03-25 08:00 - 16:00
We provide bucket truck training online and in person, to help you get the required operator qualifications.

This bucket truck operator safety training class is focused on operations and safety training for operators and ground workers. Material covered in this course:

Bucket truck setup
The mechanics of the bucket truck
Daily inspections
Working near electricity
ANSI and OSHA standards
Proper harness/belt configurations
Emergency procedures
Proper care and maintenance
Suspension trauma

This training meets or exceeds all requirements of OSHA, ANSI A92.2 and your insurance company.
There will be hands-on review of the equipment. Our trainer will go over proper pre-use inspections as well as proper setup of the bucket truck on-site. Each operator will be required to run through a variety of tasks to insure competence on the equipment. You must qualify on the equipment you use or on equipment that is the same configuration as your equipment. Please make arrangements to have your bucket truck on site for compliance.
For more information as to the content of this class, please view the description here.
Training Length:

4-5 hours safety training course
Allow 15-20 minutes per qualification
Recommend maximum of 12-14 attendees (7 minimum)

Use this form below to request more information about our bucket truck operator safety course. One of our staff will be in contact with you soon.

OPERATOR QUALIFICATIONS
In addition to equipment specific safety training, OSHA requires operators to be evaluated on the equipment they operate. While this can be done by a supervisor, most of our customers prefer a 3rd party evaluation. Operators receive a certificate as well as a wallet card which includes the make, model and serial number of the equipment they were tested on.
We offer hands-on qualification on various types of equipment including forklift, MEWP, bucket trucks and mobile cranes. We can provide the evaluations with or without a safety training class, but recommend holding both on the same day – safety training class in the morning, lunch break, qualifications in the afternoon.
Please contact our office at 508-966-4100 or use this form below to request more information. One of our staff will be in contact with you soon.

Fall Protection - Bomco - Gloucester, MA - CLOSED
2025-03-26 08:00 - 13:00
Material covered in this course:

Proper body harness donning instructions
Daily inspections of body harnesses
ANSI and OSHA standards
Proper care and maintenance
Fall protection
Suspension trauma
Basic emergency procedures

This fall protection safety training and certification is compliant with the OSHA standards 1910.140 – Personal fall protection systems, 1910.502 – Fall protection systems criteria and practices, and ANSI/ASSE Z359.11 – Safety Requirements for Full Body Harnesses.

Use this form below to request more information. One of our staff will be in contact with you soon.

Fork Truck Operator Certification with Qualifications - Kendall Green Energy/Vicinity - Cambridge MA - CLOSED
2025-03-27 06:30 - 15:00
This forklift operator safety training course is a focused operations and safety training for operators.
Industrial forklifts are covered in this class. Rough terrain forklifts can be covered by special request. Operator qualification will be performed. A completion of safety training certificate is awarded by Cranes 101. Operators who successfully pass the hands on qualification receive a Qualified Operator certificate as well as a wallet card
Material covered in this course:
Fork truck maneuvering
The mechanics of the Fork Truck
Daily inspections
Fuel/Electric storage
ANSI and OSHA standards
Safe practices
Proper care and maintenance
Physics 101
This training meets or exceeds all requirements of OSHA 1910.172
For more information as to the content of this class, please view the descriptions here. (Hyperlink the “here” to the specific page on the web site showing this class)
Training Length:
>>3 to 4 Hour Course
Use this form below to request more information. One of our staff will be in contact with you soon.

Hi Rail Gear Inspection Training - Craneworks - Brighton, CO - OPEN
2025-03-27 08:00 - 15:00
This course is best designed for experienced operators and mechanics who are interested in becoming the on-site inspectors for their company.
This course is designed to cover the Federal Railroad Administration 49 CFR 214 standards with regards to how they should be used during inspections and creating reports detailing any deficiencies and recommendations.

Course Content

How the standards apply to inspections
What equipment is made by manufacturers
Hi Rail Gear Components
Step-by-step inspection procedures

Cranes101 can bring this class to you. Please contact us to schedule your special training session.

Use this form below to request more information. One of our staff will be in contact with you soon.
